Marantec Q-7900 Manuel du propriétaire télécharger pdf (Page 14)

 Plug the operator into a properly grounded outlet (Fig. 27).

 Operator will run a self-test. All four LED’s will illuminate for

approximately 2 seconds. Then only the LED #4 will be “On”

and the operator is ready to set the adjustments.

 DO NOT operate or run the operator at this time.

PERMANENT WIRING CONNECTION:

(If required by your local electrical code)

If local codes require your operator to be connected via

permanent wiring instead of a cord and plug, your operator must

be converted, as shown in Fig. 28. Contact a qualified electrician

to run the necessary wiring to your operator and to perform the

electrical connections.

To prevent electrocution, disconnect the operator from

power and turn off power at circuit breaker for the

circuit you will be using to connect to the operator.

To prevent electrocution or fire, installation and wiring

must be done in accordance with local electrical and

building codes. DO NOT use an extension cord. DO NOT

use a 3 to 2 plug adapter. DO NOT modify or cut off the

grounding pin on the plug.

8-13. CONNECT TO POWER

To reduce the risk of electric shock, your operator is provided with

an insulated power cord with a 3-prong grounding plug. The cord

must be connected to a standard grounding outlet. If there is no

outlet available at the location, you must have a qualified

electrician install an approved grounded outlet in this area.

 Remove operator housing by removing screw underneath the

control panel cover and two screws from back of housing,

then pulling the housing away from the chassis.

 Remove screw and unsnap the power cord strain relief cover

by disengaging the tabs, and remove this part (save for

reattachment later).

 Cut the power cord leads close to where the cord enters

operator, so that after cut, there is at least 6" of wiring

remaining (white-neutral, black-hot, and green-ground) inside

the operator connected to the varistor and transformer.

 Remove the cut power cord and plug and discard. Replace

the strain relief cover by snapping tabs back into place.

 Using a hammer and screwdriver or punch, knock out conduit

hole, and bring in the permanent wiring and conduit.

 Secure conduit to chassis (method varies depending on type

of conduit used).

 Attach the incoming power leads (hot, neutral, and ground)

to the remaining internal wires using suitable wire nuts (not

provided).

 Reinstall operator housing and secure housing with screws.

Make sure that when reinstalling operator housing, no wires

will be pinched between the housing and the chassis.

 Complete the remaining installation.

 Turn on power at breaker.

Fig. 27

Grounded Outlet

Power Cord

Fig. 28

Strain Relief Cover

Conduit Nut

Remove

Wires: (remaining 6”)

Ground (Green)

Hot (Black)

Neutral (White)

8-17. ADVANCED SETTINGS (cont’d)

Level 2 – Operator settings

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Menu 1: Required driving power to OPEN (sensitivity on a scale from 1 to 16*)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Menu 2: Required driving power to CLOSE (sensitivity on a scale from 1 to 16*)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Menu 3: Automatic cut-out OPEN (sensitivity on a scale from 1 to 16*)

OFF 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Menu 4: Automatic cut-out CLOSE (sensitivity on a scale from 1 to 16*)

OFF 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

To advoid any risk of injury, Menus 3 and 4 (automatic cut-out)

may out only be switched off if a photo eyes sensor system

barrier or closing edge safety device is installed.

NOTE: Menus 5-7 are disabled

Press “+” or “-” button to scroll or navigate through menus.

Level 2: Functions overview

*The higher the setting, the higher the driving power or less sensitive operation.

Legend:

LED

off

LED on

LED flashes slowly

LED pulses

LED flashes quickly

Factory default setting

Not possible

–

1 2 ... 9 10 11 12 13 14 15 16

Commentaires sur ces manuels

Pas de commentaire

Marantec Q-7900 Manuel du propriétaire Page 14

Commentaires sur ces manuels

Produits connexes et manuels pour Ouvreur de porte de garage Marantec Q-7900