Marantec 115694 Manuel d'instructions

Marantec America Corporation5705 Centerpoint Court, Gurnee, IL 60031 U.S.A.Phone 1-888-622-2489  Fax 847-478-0348Owner’s Manual contains:Installat

108-5. ATTACH RAIL TO OPERATOR HEAD Position operator with control panel facing the back of garage. Rest operator head on cardboard or a protecti

11Cotter Ring1/4 x 3-1/4"Clevis PinFig. 19A Fig. 19BFig. 20DoorStepladderFig. 19Operator Box8-6. ATTACH RAIL TO HEADER BRACKET Support operator

12Fig. 22 Position opener head so that rail is lined up with center line of open door. Line up sturdy perforated angle (not provided) with

13 8-11. CHECK EMERGENCY RELEASETo prevent possible SERIOUS INJURY or DEATH from a falling garage door:• If possible, use emergency release handle to

148-12. INSTALL PHOTO EYE SAFETY SYSTEMMOUNTING THE PHOTO EYE SENSOR BRACKETS TO WALL: Locate the mounting position for brackets photo eye beam will

158-13. INSTALL WALL CONTROL PANEL8-14. CONNECTING WIRES TO OPERATORThe control panel must be mounted inside the garage within sight of the garage doo

16 9. CONTROL UNIT CONNECTIONS Danger of electric shock:Before any wiring work begin, make sure that the operator and all wiring is disconnected fro

1710. CONNECT TO POWERTo prevent electrocution or fire, installation and wiring must be done in accordance with local electrical and building codes. D

1811. SYSTEM SET UPFig. 41AFig. 41For proper initial operation of the operator, two basic functions must be set using the initial system programming:

1911. SYSTEM SET UP (cont’d)System initial display on control panel screen upon power ONControl PanelDisplay123System display on control panel screen

Copyright 2014 All Rights Reserved.COWNER’S MANUAL CONTENTS 1. INTRODUCTION 32. ADVANCED FEATURES 33. IMPORTANT SAFETY INFORMATION 34. T

20IMPORTANT:Upon completion of the initial set up, the operator must be cycled for two complete cycles (complete cycle comprises of one uninterrupted

2114. TRANSMITTERS13. REMOTE CONTROLSDanger of injury due to uncontrolled operation of the door!• Operate the controls or the hand transmitter only w

22Fig. 45Fig. 46CoinBatteryProgamming ButtonsLED (Indicator Lights)CHANGING THE CODE (Fig. 45):The transmitter factory preset code can be changed as f

23Fig. 49Fig. 50To test, enter the temporary PIN, then press the ENTER button. The garage door operator will activate. If the temporary PIN was set fo

24 Fig. 5314. OPERATION OF YOUR OPERATOR (cont’d)Fig. 52Lock/Vacation ButtonLight On/Off ButtonIlluminated Door Pushbutton15. HOMELINK® TRANSCEIVERREM

2517. ALIGN AND TEST PHOTO EYE SENSORSSAFETY TEST:Photo eye sensors installed on opposite sides of your door opening are intended to detect a person o

26Several important safety and instruction labels are included with your operator package. These labels must be posted inside your garage where they c

2721. TENSION ADJUSTMENTYour preassembled rail comes with the tension adjusted to factory specifications. There should be no need for further adjustme

2822. RAIL ASSEMBLY PARTSFig. 59Header EndHeader End45862137Belt Rail AssemblyModel#: M14-2807B (7' Door) M14-2808B (8' Door) Item P

2923. ACCESSORIES23-1. LED EL 300Accessories are available from your dealer. If you have difficulty locating available accessories, please contact us

3Congratulations on purchasing your Marantec® Synergy Garage Door Operator System, the most innovative operator available today. This stylishly design

3023-2. ENERGY PACK 100 (BATTERY BACKUP) IMPORTANT INSTALLATION INSTRUCTIONSTO REDUCE THE RISK OF SEVERE INJURY OR DEATH:1. READ AND FOLLOW ALL WARNIN

31 5 43 21 XN70 23-2. ENERGY PACK 100 (BATTERY BACKUP) (cont’d) Fig. 64 Fig. 68Fig. 69Fig. 70Fig. 65Fig. 67Fig. 66Energy PackP/N: 104586Light

3223-2. ENERGY PACK 100 (BATTERY BACKUP) (cont’) B3123456789020 sPPPPA 320 s greenred10. greengreenBattery ChargingBattery is LowAll Systems ar

3324. TROUBLESHOOTING FAULT DISPLAYPROBLEMSOLUTIONCODE If no buttons are pressed within 120 seconds, the programming mode terminates automati

3424. TROUBLESHOOTING (cont’d) FAULT DISPLAYPROBLEMSOLUTIONCODE Electronic defect. Have operator serviced Wall control connected incorrectly.

3525. MAINTENANCE AND ADJUSTMENTSTo ensure continued safe operation and extended life of your operator system, periodic checking for proper operation

3627. LIMITED PARTS WARRANTYMARANTEC AMERICA CORPORATIONSynergy Professional Series Residential Garage Door Opener SystemLimited Parts WarrantySynergy

37Marantec Accessories: Marantec accessories include such items as transmitters, wall controls, photo eye systems, and wireless/keyless entry systems

3829. REGISTRATION:This Warranty becomes effective upon registration at the Marantec web site: www.marantec.com. If you do not have access to the in

39

44. TOOLSFig. 1The instructions will refer to the tools shown below for proper installation, adjustment, and maintenance of the garage door operator.

40 Version: 7/14 Part #115722

55. GARAGE (cont’d)GARAGE DOOR OPERATOR SYSTEM OVERALL DIMENSIONS 7' DOOR (2.13m)6. OPERATOR PACKAGE CONTENTSFig. 5Removable serial number Rem

66. OPERATOR PACKAGE CONTENTS (cont’d)The following items are included with your Garage Door Operator (GDO). All hardware components are located in th

77. IMPORTANT INSTALLATION INSTRUCTIONSShown on the right is anoverall view of a completed garage door operator system installed on a sectional door.

88. INSTALLATION STEPS8-1. MEASURE AND MARK DOOR AREAHorizontalReinforcementBracketHeaderHorizontal Line forHeader BracketHeightDoor WidthSee Fig. 12S

9Pilot HoleCeilingHeader BracketLag ScrewFig. 13 Mark pilot holes location on header through header bracket holes where lag screws will be inser